Operating Instruction

Operation

Safe operation and point for attention

Must use the three-hole socket and three-pin plug of single phase with protective grounding.

Under environment of soak and damp, please took relevant protective measures

When operating, such as: use the protective device of leakage of electricity, put the engine on the, dry place, etc. The operator put on one's insulating gloves, in one's insulating shoes or to stand on the insulating doormat.

please use the rated voltage and fuse of standard capacity, must always remember: the wire of metal couldn't replace the fuse.

When shift the engine or pull up the plug, please don't pull and tear the electricity wire.

To operate in special environment or narrow place, must somebody look after the machine.

The personal of non-specific field could not dismantle or service the machine by oneself.

The work is through, must first cut off the electricity supply, then put work site in order, to progress maintenance and maintain the machine.

Whether operate or clean the machine must avoid sewage into the engine, if there was sewage in engine imperatively stay till the engine was dry to use.

Strictly forbid to use the engine with trouble

 

Major Component Description and Operation Characteristics

Control knob

For switching on/off circuit and controlling rotation direction of output shaft.

OFF :stop

FOR :forward rotation

REV :reversed rotation

Warning: Prior to connecting electric power sup-ply check switch first for position off.

Operate Control Handle

press the handle to move the machine clutch, which makes the flexible shaft to rotate.

Releasing the handle stops the flexible shaft rotation immediately.

Warning: The pressing force shall not exceed 20kg, preferably to the extent of locking the -flexible shaft. Do not use force multiplication tool.

Locking screw

For connecting the machine with Φ8 flexible shaft attachment and protective sleeve. Raise and insert the screw. it is simple and fast.

Note: For machines GQ-100 and GQ-150 remove the white sleeve from the machine tail first.

Warning: Switch off the machine before installing flexible shaft, protective sleeve or attachments.

Connect the flexible shaft with drills

Push the drill along 67°slider slot of the shaft to engage. This makes connection more reliable, easy and fast.

Caution: Observe through the hole of the drill to see the pop-out of the flexible shaft pin. it is only safe when the pin is out. Remove the flexible shaft.

Insert the key and push the shaft with both hands in direction

opposite to the T slot of the terminal to remove the shaft.

It saves time and manpower.

 

Method of operation

DALI drain Cleaning Machine adopted flexible cables and drilling tools of different form, made use of combined operation of high-speed rotating with propulsion by hand or automatism to drain or clear the block of pipe. So long as selected the right machine and operated to method, the block of pope will surely drain quickly. Let motor race a while with cable after clearance of block, further clear away the dirt on the wall of pipe, lastly, wash the pipe with water the effect will even better.

 

When you use the Hand Drain Cleaning Machine:

Loosen the clamping bit (or locking nut), pull out the cable.

Let cable get into the pipe till it touch the block

Lock up the clamping bit (or locking nut) with kept distance of 100mm between the pipe and cable.

Turn the cylinder (crank)and pro-pulsion the cable by hand. Then loosen clamping bit and repeat 2 and 4 move till drain of the block.

Lastly wash the cables with water clean and air-dry, get into the cylinder, to reserve.

 

When you use the Power Drain Cleaning Machine:

Let cable pass through mandrel of main engine.

Chose proper drilling tool, firmly join it and cable.

Put right place for main engine (don't bring it into contact with sewage), the drilling tool and cable get into pipe, as far as possible.

Only kept back 2~4m cable behind main engine, dismount the other cable to reserve.

Insert the plug into the three-hole socket of single phase with protective grounding.

Turn on the control knob, let the main spindle rotate clockwise.

Kept distance between the main engine and mouth of pipe (about 100~30mm) weigh down the control handle, took hold of the rotary cable mean while pushed the cable into pipe with gradually strengthen propulsive force repeatedly operate till the pipe was clear.

The work was through, pull out the cable from pipe and clean away to reserve. look out: avoid sewage on cable back to main engine or polluting interior decoration.

The work was through, let motor of main engine race about 2~3 minutes, the oiling in hole of oil, avoid rustiness.

 

When you use the portable power Drain Cleaning Machine:

The clamping bit will loosen when push the handle ② ahead, pull out the cable and introduce into the pipe at this time.

Connect with the mains, press the gearshift switch ⑤,slowly to start, then gradually quicken in skillful level.

Pressed back the handle ②,the cable be chuck while rotating and advancing.

When the cylinder rotate, the handle be push backward and forward in the light of special conditions, so that the cable could deeply ender the pipe till the block be clean and drain.

The use bas been completed, to cleaned the cable and took in cylinder, to reserve.

If you use the automatic propulsive of cable, let automatic equipment ⑥ through the top of cable then connect with front of handle and tighter up a screw. Adjust the steering switch ④,push the gearshift ⑤,the cable could automatically retreat or advance till complete the work of drain.

 

When you use the Automatic Drain Cleaning Machine:

Let cable pass through the hollow axle of main engine, then connect with proper drilling tool.

Put the main engine on the proper place, insert the cable into the pipe to the full. Insert the plug in three-hole socket of single-phase with the protective grounding. Turned the control switch ① to pointed clockwise, then push down the handle ④ the cable could autld automatically advance toward, turn the gearshift knob ③ the forward speed of cable is change.

Look out: when encounter the resistance to forward movement, must change the direction and adjust speed, not blindly, refrain damage.

The use has been completed, please cleaned the cables to reserve.

Soon after main engine race 2~3 minutes, to oiling, to reserve.

 

When you use the pneumatic Drain Cleaning Machine:

Chose an assembly way of exhaust pipe with seal plug in accordance with form of mouth of pipe.

pull the handle of inflator between upward and downward to inflate bring pressure to bear upon block under0.4Mpa.in degrees of blockage glued to looked carefully the barometer at all time, the needle not go beyond, the red security line.

Pour fully water into the pipe, let seal plug closely hold down the mouth of pipe, quickly lift up the handle of valve, made use the impulsive force of airflow to drain, bring about good results from duplicate operation.

If the mouth of pipe be plug up, so that the pneumatic machine is mot erect, please to join the seal plug with soft pipe, strain to press the seal plug with hands and quickly aerate.